Quick

  • HOME

Adafruit Qualia ESP32-S3 for TTL RGB-666 Displays[5800]

Adafruit Qualia ESP32-S3 for TTL RGB-666 Displays
  • Adafruit Qualia ESP32-S3 for TTL RGB-666 Displays[5800]

    보여지는 사진은 제품을 대표적으로 묘사하는 사진입니다. 정확한 규격은 제품의 데이터시트에서 확인하셔야 합니다.

      • 해외
    • 소비자가
      38,500
    • (vat 포함)
      42,350원
    • 상품코드
      P015450766
    • 제 조 사
      Adafruit
    • 마일리지
      190 IC
      마일리지 INFO

      마일리지 적립금은 상품 구매시 적립되는 형태가 아닌, 프로모 션 진행 시 혜택으로 적립되는 형태입니다. 자세한 관 련 내용을 보시려면 마이페이지>마일리지 메뉴에서 확 인하세요!

    • 배송기간
      1주이내
    • 재고위치
      해외 재고
    • 최소구매수량
      1개
    • 수량선택
    총 합계 38,500 원 (vat 별도)
    42,350 원 (vat 포함)
    연구비카드사용가능
  • 이 상품의 상품코드는 P015450766 입니다.

    Adafruit Qualia ESP32-S3 for TTL RGB-666 Displays[5800]

    There's a few things everyone loves: ice cream, kittens, and honkin' large TFT screens. We're no strangers to small TFT's - from our itsy 1.14" color display that graces many-a-TFT-Feather to our fancy 3.5" 320x480 breakout screen. But most people who dabble or engineer with microcontrollers know that you sort of 'top out' at 320x480 - that's the largest resolution you can use with every day SPI or 8-bit 8080 interfaces. After that, you're in TTL-interface TFT land, where displays no longer have an internal memory buffer and instead the controller has to continuously write scanline data over a 16 or 18 or 24 pin interface.

    RGB TTL interface TFT displays can get big: they start out at around 4.3" diagonal 480x272, and can get to 800x480, 800x600 or even 720x720. For displays that big, you need a lot of video RAM (800x480 at 24 bit color is just over 1MB), plenty of spare GPIO to dedicate, and a peripheral that will DMA the video RAM out to the display continuously. This is a setup familiar to people working with hefty microcontrollers or microcomputers, the sort of device that run cell phones, or your car's GPS navigation screen. But until now, nearly impossible to use on low cost microcontrollers.

    The ESP32-S3 is the first low-cost microcontroller that has a built in peripheral that can drive TTL displays, and can come with enough PSRAM to buffer those large images. For example, on the Adafruit Qualia ESP32-S3 for TTL RGB-666 Displays, we use a S3 module with 16 MB of Flash and 8 MB of octal PSRAM. Using the built in RGB display peripheral you can display graphics, images, animations or even video (cinepak, natch!) with near-instantaneous updates since the whole screen gets updated every ~30FPS.

    This dev board is designed to make it easy for you to explore displays that use the "secondary standard' 40-pin RGB-666 connector. This pin order is most commonly seen on square, round and bar displays. You'll want to compare the display you're using to this datasheet, if it matches you'll probably be good! One nice thing about this connector ordering is that it also includes pins for capacitive touch overlay, and we wire those up to the ESP32-S3's I2C port so you can also have touch control with your display.

    Don't forget! This is just the development board, a display is not included. Use any RGB-666 pinout display with or without a touch overlay. Note that you will need to program in the driver initialization code, dimensions, and pulse widths in your programming language. Here are some known-working displays that you can use in Arduino or CircuitPython:

    On the Qualia board we have the S3 modules, with 16 pins connected to the TFT for 5-6-5 RGB color, plus HSync, VSync, Data Enable and Pixel Clock. There's a constant current backlight control circuit using the TPS61169 which can get up to 30V forward voltage and can be configured for 25mA-200mA in 25mA increments (default is 25mA). Power and programming is provided over a USB C connector, wired to the S3's native USB port. For debugging, the hardware UART TX pin is available as well.

    Since almost every GPIO is used, and almost all RGB-666 displays need to be initialized over SPI, we put a PCA9554 I/O expander on the shared I2C bus. Arduino or CircuitPython can be instructed on how to use the expander to reset and init the display you have if necessary. The remaining expander pins are connected to two right-angle buttons, and the display backlight. 

    The expander is what lets us have a full 4-pin SPI port and two more analog GPIO pins - enough to wire up an MMC in 1-wire SDIO mode along with an I2S amplifier to make an A/V playback demo. Maybe we can even eat ice cream while watching kitten vids! There is also the shared I2C port, we provide a Stemma QT / Qwiic port for easy addition of any sensor or device you like.

확대보기

문의하기

Adafruit Qualia ESP32-S3 for TTL RGB-666 Displays[5800]

문의유형
제목
내용
답변알림
      • @
      • -
      • -

공유하기

대량구매 문의

상품명 Adafruit Qualia ESP32-S3 for TTL RGB-666 Displays[5800]
성명
업체명
연락처
이메일
    • @
수량
유의사항
  • ※ 대량 구매문의를 해주셔서 감사합니다.
  • 문의가 접수 되는대로 빠른 시간내에 연락을 드리도록 하겠습니다.

신규 프로젝트

프로젝트 추가

결제 및 주문

  • 공정거래위원회
  • 홈택스
  • 연구비결제
  • 이노비즈
  • 마우저
  • 에스크로
  • 기업금융

공지사항 목록