• HOME

ESP32-C3-DevKit-RUST-1 - 4 MB Flash[5787]

ESP32-C3-DevKit-RUST-1 - 4 MB Flash
  • ESP32-C3-DevKit-RUST-1 - 4 MB Flash[5787]

    보여지는 사진은 제품을 대표적으로 묘사하는 사진입니다. 정확한 규격은 제품의 데이터시트에서 확인하셔야 합니다.

      • 해외
    • 소비자가
    • (vat 포함)
    • 상품코드
    • 제 조 사
    • 마일리지
      190 IC
      마일리지 INFO

      마일리지 적립금은 상품 구매시 적립되는 형태가 아닌, 프로모 션 진행 시 혜택으로 적립되는 형태입니다. 자세한 관 련 내용을 보시려면 마이페이지>마일리지 메뉴에서 확 인하세요!

    • 배송기간
    • 재고위치
      해외 재고
    • 최소구매수량
    • 수량선택
    총 합계 38,900 원 (vat 별도)
    42,790 원 (vat 포함)
  • 이 상품의 상품코드는 P015279144 입니다.

    ESP32-C3-DevKit-RUST-1 - 4 MB Flash[5787]

    ESP32-C3-DevKit-RUST-1 is an entry-level RISC V development board equipped with the ESP32-C3-MINI-1, a powerful, generic Wi-Fi + Bluetooth LE MCU module that features a rich set of peripherals, yet an optimized size. It's an ideal choice for a wide variety of application scenarios related to the Internet of Things (IoT), such as embedded systems, smart homes, wearable electronics, etc. This version is equipped with the ESP32-C3-MINI-1 with 4MB SPI Flash and no PSRAM.

    Please note: The C3 is similar  to the ESP32 - but uses RISC V as a core, not Tensilica, and has Bluetooth LE (not classic!) However, there is minimal support for this dev board. For example, as of the time of this writing, there is no CircuitPython support - only Arduino and ESP IDF! Please purchase if you're doing development with the C3, and recognize that it's a different core than the classic ESP32s most folks have used.

    Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-C3-DevKit-RUST-1 on a breadboard. Please note: header is not included.

    At the core of the module is ESP32-C3, which has a 32-bit RISC-V single-core processor. The ESP32-C3 integrates a rich set of peripherals, ranging from UART, I2C, I2S, remote control peripheral, LED PWM controller, general DMA controller, TWAI controller, USB Serial/JTAG controller, temperature sensor, and ADC. It also includes SPI, Dual SPI, and Quad SPI interfaces.

    This special board, designed for following the Rust Training Program comes with:

    • The ESP32-C3-MINI-1 module
    • A 6-DoF IMU - ICM-42670-P
    • Temperature and humidity sensor - SHTC3
    • Li-Ion battery charger  
    • Type-C USB

    The board is designed to be easily used in training sessions, demonstrating Rust capabilities with all the board peripherals.

    ESP32-C3 SoC Features

    • IEEE 802.11 b/g/n-compliant
    • Bluetooth 5, Bluetooth mesh
    • 32-bit RISC-V single-core processor, up to 160MHz
    • 384 KB ROM
    • 400 KB SRAM (16 KB for cache)
    • 8 KB SRAM in RTC
    • 22 × programmable GPIOs
    • 3 × SPI
    • 2 × UART
    • 1 × I2C
    • 1 × I2S
    • 2 × 54-bit general-purpose timers
    • 3 × watchdog timers
    • 1 × 52-bit system timer
    • Remote Control Peripheral (RMT)
    • LED PWM controller (LEDC)
    • Full-speed USB Serial/JTAG controller
    • General DMA controller (GDMA)
    • 1 × TWAI®
    • 2 × 12-bit SAR ADCs, up to 6 channels
    • 1 × temperature sensor



ESP32-C3-DevKit-RUST-1 - 4 MB Flash[5787]

      • @
      • -
      • -


대량구매 문의

상품명 ESP32-C3-DevKit-RUST-1 - 4 MB Flash[5787]
    • @
  • ※ 대량 구매문의를 해주셔서 감사합니다.
  • 문의가 접수 되는대로 빠른 시간내에 연락을 드리도록 하겠습니다.

신규 프로젝트

프로젝트 추가

결제 및 주문

  • 공정거래위원회
  • 홈택스
  • 연구비결제
  • 이노비즈
  • 마우저
  • 에스크로
  • 기업금융

공지사항 목록