Quick

  • HOME

Adafruit Feather RP2040 with USB Type A Host[5723]

Adafruit Feather RP2040 with USB Type A Host
  • Adafruit Feather RP2040 with USB Type A Host[5723]

    보여지는 사진은 제품을 대표적으로 묘사하는 사진입니다. 정확한 규격은 제품의 데이터시트에서 확인하셔야 합니다.

      • 해외
    • 소비자가
      34,100
    • (vat 포함)
      37,510원
    • 상품코드
      P014839077
    • 제 조 사
      Adafruit
    • 마일리지
      170 IC
      마일리지 INFO

      마일리지 적립금은 상품 구매시 적립되는 형태가 아닌, 프로모 션 진행 시 혜택으로 적립되는 형태입니다. 자세한 관 련 내용을 보시려면 마이페이지>마일리지 메뉴에서 확 인하세요!

    • 배송기간
      1주이내
    • 재고위치
      해외 재고
    • 최소구매수량
      1개
    • 수량선택
    총 합계 34,100 원 (vat 별도)
    37,510 원 (vat 포함)
    연구비카드사용가능
  • 이 상품의 상품코드는 P014839077 입니다.

    Adafruit Feather RP2040 with USB Type A Host[5723]

    You're probably really used to microcontroller boards with USB, but what about a dev board with two? Two is more than one, so that makes it twice as good! And the Adafruit Feather RP2040 with USB Host is definitely double-the-fun of our other Feather RP2040 boards, with a USB Type A port on the end for connecting USB devices to. 

    Now you might be thinking "hey waitaminute, the RP2040 doesn't have two USB port peripherals???" and you'd be correct! But what it does have is a nifty PIO peripheral that can be (ab)used to emulate a USB host peripheral. You get to keep the main USB port for uploading, debugging, and data communication, while at the same time sending and receiving data to just-about-any USB device. This work is originally by sekigon on GitHub, and if you're using Pico SDK that's still the recommended library to use.

    Currently, support for the USB Host peripheral is only in Arduino. So check out the TinyUSB 'dual role' examples for some things you can do! For example, datalogging to a USB Key. Or reading from another device/microcontroller that has USB CDC serial interface. Or creating an HID re-mapper. Or connecting to weird devices that require firmware-updates like the Cypress EZ-USB based Intellikeys communications board.

    Note that this is definitely a firmware hack: you will need to dedicate the second ARM core and both PIO peripherals to just handling the USB messages, but we find that it does work fairly well, or at least as well as most microcontroller's USB Host peripherals!

    We also include a 1 Amp boost converter based on the TPS61023 so you can run from Lipo battery and get a nice clean 5V output for the USB devices. The booster has the enable pin tied to one of the extra GPIO on the RP2040 so power can be manually turned on and off to hard-reset whatever is connected.

    At the Feather's heart is an RP2040 chip, clocked at 133 MHz and at 3.3V logic, the same one used in the Raspberry Pi Pico. This chip has a whopping 8MB of onboard QSPI FLASH and 264K of RAM!  There's even room left over for a STEMMA QT connector for plug-and-play of I2C devices!

    To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built-in battery charging. You don't need a battery, it will run just fine straight from the USB Type C connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when it's available.

    Here're some handy specs! You get:

    • Measures 2.0" x 0.9" x 0.28" (50.8mm x 22.8mm x 7mm) without headers soldered in
    • Light as a (large?) feather - 6.3 grams
    • RP2040 32-bit Cortex M0+ dual core running at ~133 MHz @ 3.3V logic and power
    • 264 KB RAM
    • 8 MB SPI FLASH chip for storing files and CircuitPython/MicroPython code storage. No EEPROM
    • Tons of GPIO! 21 x GPIO pins with following capabilities:
      • Four 12-bit ADCs (one more than Pico)
      • Two I2C, Two SPI, and two UART peripherals, we label one for the 'main' interface in standard Feather locations
      • 16 x PWM outputs - for servos, LEDs, etc
    • Built-in 200mA+ lipoly charger with charging status indicator LED
    • Pin #13 red LED for general purpose blinking
    • RGB NeoPixel for full-color indication.
    • On-board STEMMA QT connector that lets you quickly connect any Qwiic, STEMMA QT or Grove I2C devices with no soldering!
    • Both Reset button and Bootloader select button for quick restarts (no unplugging-replugging to relaunch code)
    • USB Type C connector lets you access built-in ROM USB bootloader and serial port debugging
    • USB Type A connector for USB host capability. D+ on GPIO 16, D- on GPIO 17
    • 5V Boost converter, up to 1 Amp peak output for USB peripheral power, with 500mA resettable fuse. Enable on GPIO 18. 
    • 3.3V Power/enable pin
    • 4 mounting holes
    • 12 MHz crystal for perfect timing.
    • 3.3V regulator with 500mA peak current output

    https://www.youtube.com/embed/WxLDsQwKVpY?start=170

확대보기

문의하기

Adafruit Feather RP2040 with USB Type A Host[5723]

문의유형
제목
내용
답변알림
      • @
      • -
      • -

공유하기

대량구매 문의

상품명 Adafruit Feather RP2040 with USB Type A Host[5723]
성명
업체명
연락처
이메일
    • @
수량
유의사항
  • ※ 대량 구매문의를 해주셔서 감사합니다.
  • 문의가 접수 되는대로 빠른 시간내에 연락을 드리도록 하겠습니다.

신규 프로젝트

프로젝트 추가

결제 및 주문

  • 공정거래위원회
  • 홈택스
  • 연구비결제
  • 이노비즈
  • 마우저
  • 에스크로
  • 기업금융

공지사항 목록