Quick

  • HOME

Adafruit 1.2" 4-Digit 7-Segment Display w/I2C Backpack - Red[1270]

Adafruit 1.2" 4-Digit 7-Segment Display w/I2C Backpack - Red
  • Adafruit 1.2

    보여지는 사진은 제품을 대표적으로 묘사하는 사진입니다. 정확한 규격은 제품의 데이터시트에서 확인하셔야 합니다.

      • 해외
    • 소비자가
      견적문의요망
    • 상품코드
      P014222728
    • 제 조 사
      Adafruit
    • 마일리지
      0 IC
      마일리지 INFO

      마일리지 적립금은 상품 구매시 적립되는 형태가 아닌, 프로모 션 진행 시 혜택으로 적립되는 형태입니다. 자세한 관 련 내용을 보시려면 마이페이지>마일리지 메뉴에서 확 인하세요!

    • 배송기간
      1주이내
    • 재고위치
      해외 재고
    • 최소구매수량
      1개
  • 이 상품의 상품코드는 P014222728 입니다.

    Adafruit 1.2" 4-Digit 7-Segment Display w/I2C Backpack - Red[1270]

    What's better than a single LED? Lots of LEDs! A fun way to make a numeric display is to use a 4-digit 7-segment display. LED matrices like these are 'multiplexed' - so to control all the seven-segment LEDs you need 14 pins. That's a lot of pins, and there are driver chips like the MAX7219 that can control a matrix for you but there's a lot of wiring to set up and they take up a ton of space. Here at Adafruit we feel your pain! After all, wouldn't it be awesome if you could control a matrix without tons of wiring? That's where these adorable LED matrix backpacks come in. We have them for a variety of 8x8 and 7-segment displays. They work perfectly with the displays we stock in the Adafruit shop and make adding a bright display trivial.

    The backpacks use a driver chip that does all the heavy lifting for you: They have a built in clock so they multiplex the display. They use constant-current drivers for ultra-bright, consistent color (the images above are photographed at the dimmest setting to avoid overloading our camera!), 1/16 step display dimming, all via a simple I2C interface. The backpacks come with address-selection jumpers so you can connect up to eight 7-segments (or a combination, such as four mini 8x8's and four 7-segments, etc) on a single I2C bus.

    Since this display has two LEDs per segment in series we need to power from 5V, even when using 3V logic. However, the chip really prefers the IO signals to be close to the power voltage. If you're using a board with higher-than-5V power, like Raspberry Pi's that tend to be powered by 5.25~5.5V, you may want to add a diode between the power supply output and the power input, to reduce it down.

    The product kit comes with:

    A bit of soldering is required to attach the matrix onto the backpack but its very easy to do and only takes about 5 minutes.

    Of course, in classic Adafruit fashion, we also have a detailed tutorial showing you how to solder, wire and control the display. We even wrote very nice libraries for the backpacks so you can get running in under half an hour, displaying numbers on the 7-segment for either Arduino or Raspberry Pi. If you've been eyeing matrix displays but hesitated because of the complexity, his is the solution you've been looking for!

    //www.youtube.com/embed/zG_O0Clu4jI?rel=0&start=110&autoplay=0

    Adafruit 1.2" 4-Digit 7-Segment Display w/I2C Backpack Red (1:50)

확대보기

문의하기

Adafruit 1.2" 4-Digit 7-Segment Display w/I2C Backpack - Red[1270]

문의유형
제목
내용
답변알림
      • @
      • -
      • -

공유하기

대량구매 문의

상품명 Adafruit 1.2" 4-Digit 7-Segment Display w/I2C Backpack - Red[1270]
성명
업체명
연락처
이메일
    • @
수량
유의사항
  • ※ 대량 구매문의를 해주셔서 감사합니다.
  • 문의가 접수 되는대로 빠른 시간내에 연락을 드리도록 하겠습니다.

신규 프로젝트

프로젝트 추가

결제 및 주문

  • 공정거래위원회
  • 홈택스
  • 연구비결제
  • 이노비즈
  • 마우저
  • 에스크로
  • 기업금융

공지사항 목록