Quick

  • HOME

[1869]Hot Air Soldering Rework Station w/ Three Nozzles

Hot Air Soldering Rework Station w/ Three Nozzles
  • [1869]Hot Air Soldering Rework Station w/ Three Nozzles

    보여지는 사진은 제품을 대표적으로 묘사하는 사진입니다. 정확한 규격은 제품의 데이터시트에서 확인하셔야 합니다.

      • 무료
      • 해외
    • 소비자가
      견적문의요망
    • 상품코드
      P013158151
    • 제 조 사
      Adafruit
    • 마일리지
      1,170 IC
      마일리지 INFO

      마일리지 적립금은 상품 구매시 적립되는 형태가 아닌, 프로모 션 진행 시 혜택으로 적립되는 형태입니다. 자세한 관 련 내용을 보시려면 마이페이지>마일리지 메뉴에서 확 인하세요!

    • 배송기간
      1주이내
    • 재고위치
      해외 재고
    • 최소구매수량
      1개
  • 이 상품의 상품코드는 P013158151 입니다.

    [1869]Hot Air Soldering Rework Station w/ Three Nozzles

    If you've ever made a mistake when surface-mount soldering, you'll know how much of a pain it can be to fix it without the right tools. It can add critical time to a project and can seriously dampen your soldering momentum if you run into a bad component or a faulty reflow. With the Quick 957D Soldering Station, you can easily rework your boards and get your project back on track. Its also possible to use solder paste (in a syringe for example) to apply paste and then blow hot air over it to melt the solder and get the components into place.

    This essential tool has an internal pump and heater to blow a steady stream of temperature controlled hot air to make it super easy to remove components, fix joints and jumpers, replace missing components, or just correct something you've done wrong. The Quick 957D is great for beginners because of it's low price and relative ease of use, there's also different nozzles for different sized parts.

    It has a closed-loop temperature control range between 100-450°C (212-842°F) and a digital display so you can easily tell what temperature the air's blowing at. It has a power consumption of 580W and an intelligent cooling system so the airflow remains on until it gets to below 100°C. Max air flow is 100L/minute - but for most work you'll want to keep it a lot lower than that.

    Just make sure to let the rework station heat up all the way before using it and be careful to use tools and not your hands when using as it spits out, well, really hot air. Comes with three nozzles, use the smallest size you can get away with - they help avoid damaging other components if you are trying to isolate one part of the board while avoiding a connector for example.

    https://www.youtube.com/embed/inX2fgtVk5c

    //www.youtube.com/embed/zTgSLqpGHCg?start=708

확대보기

문의하기

[1869]Hot Air Soldering Rework Station w/ Three Nozzles

문의유형
제목
내용
답변알림
      • @
      • -
      • -

공유하기

대량구매 문의

상품명 [1869]Hot Air Soldering Rework Station w/ Three Nozzles
성명
업체명
연락처
이메일
    • @
수량
유의사항
  • ※ 대량 구매문의를 해주셔서 감사합니다.
  • 문의가 접수 되는대로 빠른 시간내에 연락을 드리도록 하겠습니다.

신규 프로젝트

프로젝트 추가

결제 및 주문

  • 공정거래위원회
  • 홈택스
  • 연구비결제
  • 이노비즈
  • 마우저
  • 에스크로
  • 기업금융

공지사항 목록