Quick

  • HOME

BLEBee v2.0.0 [114990259]

The BLEBee is a Bluetooth Smart enabled XBEE form factor module based on Bluegiga’s BLE113 M256K module.
  • BLEBee v2.0.0 [114990259]

    보여지는 사진은 제품을 대표적으로 묘사하는 사진입니다. 정확한 규격은 제품의 데이터시트에서 확인하셔야 합니다.

      • 무료
      • 해외
    • 소비자가
      견적문의요망
    • 상품코드
      P006161501
    • 제 조 사
      seeedstudio
    • 마일리지
      290 IC
      마일리지 INFO

      마일리지 적립금은 상품 구매시 적립되는 형태가 아닌, 프로모 션 진행 시 혜택으로 적립되는 형태입니다. 자세한 관 련 내용을 보시려면 마이페이지>마일리지 메뉴에서 확 인하세요!

    • 배송기간
      7일~10일 이내
    • 재고위치
      해외 재고
    • 최소구매수량
      1개
  • 이 상품의 상품코드는 P006161501 입니다.

    BLEBee v2.0.0 [114990259]

    해당 제품은 재고 소진 해외에서 입고가 되는 제품으로 납기가 7~10일 정도 소요될 수 있습니다.  

     

    BLEBee v2.0.0 based on Bluegiga’s BLE113 Module

     
    The BLEBee is a Bluetooth Smart enabled XBEE form factor module based on Bluegiga’s BLE113 M256K module. The BLEBee can be used in hardware setups, where normally an XBEE module is used. Using a BLEBee an XBee socket enabled embedded system can communicate with desktop computers, smartphones, table computers and even other embedded systems providing Bluetooth Smart aka Bluetooth Low Energy (BLE) or Bluetooth 4.0.
     
     
    Features: 
    • Based on Bluegiga’s BLE113-M256K Bluetooth 4.0 single mode compliant module
    • Open Source Hardware- and Firmware
    • No Library necessary to operate the module on the target platform
    • Compatible with BLE enabled smartphones and tablets 
    • Baudrates 9600 (default), 14400, 19200, 28800, 38400, 57600 and 112500 can be changed using a characteristic
    • Assoc pin is controlled by the BLEBee to indicate a connection
    • Reset pin can be used to reset the BLEBee
    • Supports OTA firmware upgrades e.g. using BLEGUI2 tool from Bluegiga or M.Kroll’s BLExplr iPhone App
     
    Specification:
     
    Services and Characteristics:
     
    Service
     
    BLEBee Service v2.0.0: 067978AC-B59F-4EC9-9C09-2AB6E5BDAD0B
     
    Characteristics
     
    Bluetooth Device Address (Read): 067978AC-B69F-4EC9-9C09-2AB6E5BDAD0B
     
    Baudrate (read, write): 067978AC-B79F-4EC9-9C09-2AB6E5BDAD0B
     
    Supported baudrate values are:
    • 0x00 = 9600 Baud (default)
    • 0x01 = 14400 Baud
    • 0x02 = 19200 Baud
    • 0x03 = 28800 Baud
    • 0x04 = 38400 Baud
    • 0x05 = 57600 Baud
    • 0x06 = 112500 Baud
    The baudrate setting is written to the internal storage of the BLE113 module, so the setting will persist even if you remove power from the module. During the next boot cycle after power cycling the module or resetting it, the baudrate setting is restored from flash. So there is no need to reconfigure the BLEBee every time you power the module.
     
    Enable Connect LED (read, write): 067978AC-B89F-4EC9-9C09-2AB6E5BDAD0B
     
    This new characteristic is used to change the bahavior of the blue LED on the BLEbee which indicates the connection status of the BLEBee.
    Supported values are:
    • 0x00 = LED is not used to indicate a connection (Default)
    • 0xFF = LED is used to indicate a connection.
    So don’t worry if the LED is not turned on while connected if you are using the BLEBee the first time. It is turned off by default. You need to change the characteristic first to 0xFF in order to use the LED. The setting is also persisted into the BLEBees flash memory, so the setting persists between power and reset cycles.
     
    Data (Write, Indicate): 067978AC-B99F-4EC9-9C09-2AB6E5BDAD0B
     
    The Data characteristic is new to the BLEBee v2.0.0. If you connect the BLEBee from e.g. an iOS Device and you enable indications on this characteristic, the iOS device will be indicated whenever the embedded device sends serial data to the BLEBee on the TX pin. If you write data from the iOS device to the BLEBee the data is send available on the RX pin of the BLEBee.
     
    Service
     
    BlueGiga OTA Service: 1d14d6ee-fd63-4fa1-bfa4-8f47b42119f0
     
    This is the OTA service which is implemented on the BLEBee as Bluegiga describes it in the Application Note: Implementing OTA Firmware Upgrade
     
    Characteristics
     
    OTA Control Characteristic: f7bf3564-fb6d-4e53-88a4-5e37e0326063
     
    The OTA control point characteristic is used to control the firmware upgrade process between the device that will be updated and the device that performs the update it is a write only attribute to the control can only made by the device that performs the update.
     
    OTA Data Characteristic: 984227f3-34fc-4045-a5d0-2c581f81a153
     
    The data cahracteristic is on the other hand used to transmit the data from the device that performs the update to the device that is being updated.
     
    iPhone App:
    In order to access the features of the BLEBee such as controlling baud rate, the connection LED, the output channels and the serial port the iPhone App BLExplr is recommended: https://apps.apple.com/us/app/blexplr/id524018027
     
    Design Files and Firmware:
    The Schematic, Boardfiles and Firmware sources and Arduino FIO sketches are available at the authors github repository 
     
    Support:
    Please visit the authors BLEBee v2.0.0 Blog
    or Dr. Michael Kroll’s Mobile Computing Forum about the BLEBee v2.0.0.

확대보기

문의하기

BLEBee v2.0.0 [114990259]

문의유형
제목
내용
답변알림
      • @
      • -
      • -

공유하기

대량구매 문의

상품명 BLEBee v2.0.0 [114990259]
성명
업체명
연락처
이메일
    • @
수량
유의사항
  • ※ 대량 구매문의를 해주셔서 감사합니다.
  • 문의가 접수 되는대로 빠른 시간내에 연락을 드리도록 하겠습니다.

신규 프로젝트

프로젝트 추가

결제 및 주문

  • 공정거래위원회
  • 홈택스
  • 연구비결제
  • 이노비즈
  • 마우저
  • 에스크로
  • 기업금융

공지사항 목록